How to connect an inverter to a car battery

With an inverter you will never be bored on the road.

From keeping your DVD player, laptop running, to charging your cellphones and iPads on the go, these devices will keep your devices running whenever they’re available.

Then I’ll teach you how to connect the inverter to your car battery to make your road trips, outdoor activities and more even more exciting.

How to connect inverter to car battery

Before you even think about how to connect the inverter to the car battery, you need to choose a suitable place to place the device:

Likely options include the trunk, glove box, cabin, and more.

Whatever your choice, it is important that you operate your inverter from a location that meets the following conditions:

  • Ventilation: Due to the heat produced by inverters, keep your device only in a well-ventilated place. Check what your owner’s manual recommends regarding clearance around your equipment for maximum airflow.
  • Accessibility – For convenience, you want the inverter to be located where you can easily reach it.
  • Battery location: Since you don’t want to use a lot of cables (it might look ugly), it’s nice that your ideal location isn’t that far from the battery compartment. However, you should not operate the inverter from the battery compartment of the car, as this can pose a fire hazard (eg combustible gases in the battery).

Locations to keep off

To be clear, here are some locations to avoid when it comes to selecting a location for your inverter:

  • On the floor above your car’s exhaust system and other areas that experience extreme temperatures, such as under the hood.
  • Enclosed areas where moisture can condense.
  • Places where you are likely to find flammable fuel vapors.

Excessive heat will shorten the life of your investment because condensers are extremely temperature sensitive.

Also, inverters are easily damaged by liquids and you risk your life if you bring them into contact with moisture or rain.

The best battery for use with an inverter

How to connect inverter to car battery: Installation procedure

Having settled in the right place for our inverter to work, let’s now move on to the actual installation:

1. Mount the power inverter

Bring your device to the car and lay it completely flat (or fairly flat) in the designated spot.

Inverters should always operate on flat surfaces such as the floor of the vehicle.

As mentioned above, make sure to leave some space around your device.

This allows the warm air to escape from the inverter.


2.Tackle the fuse

Before proceeding with the installation of the fuse holder, make sure your inverter is turned off for safety reasons.

Keep in mind that without a fuse, the inverter is prone to problems such as short circuits and can easily catch fire and damage your car.

There are two possibilities here:

  • He was lucky and ordered a unit that already had the fuse set on it.
  • Your inverter is not installed with a fuse and you must mount it before completing the rest of the wiring.

If you belong to the lucky group, congratulations! Go to step 3.

Those who belong to the “unlucky” fate should follow this procedure:

  1. Place the fuse holder in a safe place near the battery.
  2. Remove the fuse holder cover, top nut and washers from the fuse posts.
  3. Place the fuse on top of the bottom ring on the two posts.
  4. Attach the connector to the shorter red wire at the end of the fuse to the post closest to your battery.
  5. Add a ring to the top of the connector. Tighten the nut.
  6. Replace the connector on the long red wire on the fuse end of the remaining pole.
  7. Place a washer back on the connector. Tighten the nut.
  8. Finally, replace the fuse holder cover and secure the cover with cable ties or insulating tape.

Best 2000 Watt Inverter Generator for the Money

Reminder: Your inverter may be different from mine and it is best to continue to refer to your owner’s manual for specific steps in your case.


3. Complete the remaining wiring

The final steps are quite simple and involve connecting the rest of the wiring.

Correct steps:

  • Connect the positive (+) connector, marked red, to the positive terminal of your inverter.
  • Also hook the negative (-) connector – marked black – to the negative terminal of your inverter.
  • Connect the ground wire connector to the ground terminal (copper) of the inverter when prompted.
  • Tighten the nuts on each connection until they are snug.
  • Route the red and black wires to the battery and connect the black wires to the negative battery terminal first. Keep in mind that you connect the red (plus) wire to the battery a little later.
  • Route the ground wire to a bare metal on the body of your vehicle and connect the other end there. You can even drill a hole and screw there.

4.Recheck your connections

You’re almost done now, but you need to make sure you’ve made the connections correctly.

Go back and check the connections on the terminals, both on the inverter and on the battery.

You want to make sure they are sturdy enough; a loose connection can cause the cables to build up heat, which can damage your equipment.

The other part you need to focus on are the cables/connectors; contact between them and a metal part can be dangerous.

That’s all!


5.Finish the installation

The last step is the easiest…

Connect the hanging end of the red wire to the positive (+) battery terminal.

All you need to do now is turn on your inverter to see if you’ve done all the homework correctly.

Hopefully it works.

How to hook up an inverter to a car battery: Additional safety tips

  • Your vehicle must be turned off while performing the steps described.
  • Never work on electrical systems while drinking, in the rain or under medication.
  • Disconnect the positive battery terminal before connecting the inverter to the device.
  • Use recommended cables to protect your system and maximize inverter efficiency.
  • To avoid accidents, remove metal jewelry and items such as watches.

These are just general guidelines and the instructions for your device may vary slightly.

 

 

Fortunately, most inverters have clear installation instructions in the manual and even come with essential supplies such as cables and fuse sets to simplify the procedure.

Follow what the manufacturer has written along with these tips while mounting the inverter in your car.

Leave a Comment